4-8 NPSH NPSH (pipe-size hose) External Thread Specifications
4-8NPSH EXT
ASMESTD: ASME B1.20.7SOURCE: Table 2 · p. 5TYPE: External (bolt/screw)CLASS: StdSERIES: NPSH (pipe-size hose)
Major diameter
4.4683 – 4.4461
max – min
Pitch diameter
4.3871 – 4.3760
max – min
Minor diameter
4.3059 – 4.2768
max – min
Pitch
0.12500
8 threads per inch
Thread profile
4-8NPSH EXT: solid line = maximum material profile, dashed = minimum material, hatched = tolerance zone, grey dashed = basic profile. Drawn to scale; values in inches, diameters shortened.
Limits of size, class Std
| Dimension | Basic | Max | Min | Tolerance |
|---|---|---|---|---|
| Major diameter dPara. 3.1: tolerance = 2 × PD tolerance | 4.4803 | 4.4683 | 4.4461 | 0.0222 |
| Pitch diameter d2 | 4.3991 | 4.3871 | 4.3760 | 0.0111 |
| Minor diameter d1Max printed; min is a reference value | 4.3179 | 4.3059 | 4.2768ref. | 0.0291ref. |
| Allowance es | 0.0120 |
Dimensions in inches. Values are those of the standard (ASME B1.20.7); calculated cells follow the standard’s formulas. Where the standard prints a value that differs from its formula, the printed value is shown with a note.
Tolerance zones relative to the basic size, inches
Mating, gaging and dimensions
Mating member and fit at the limits
- Service
- Steam, air, water, and all other hose connections to be made up with standard pipe threads
- Mating group (compatible designations)
- NPSH-4
- Mating member of the same designation
- 4-8NPSH INT
- Other designations in the mating group
- none (mates only with its own designation)
- Minimum PD clearance (coupling min − nipple max)
- 0.0120 in
- Maximum PD clearance (coupling max − nipple min)
- 0.0342 in
- Minimum major dia clearance
- 0.0120 in
- Minimum minor dia clearance
- 0.0120 in
- Fit at the limits (PD)
- clearance (always)
Lead, flank and profile
- Lead variation ± (Table 5) ±δP
- 0.0032 in
- Half-angle variation ± (Table 5) ±δα
- 1° 42′
- Lead angle at the basic PD λ
- 0° 31′
- Crest flat (basic P/8)
- 0.015625 in
- Root flat (basic P/8)
- 0.015625 in
- Extreme flat P/24 at minimum PD
- 0.005208 in
- Root radius for the model (worn tool) r
- 0.013532 in
Table 4 dimensions (nipple and coupling)
- As printed
- C 4 1/32; OD 4 15/32; L 1 1/8; l 1/4
- Inside diameter of the nipple C
- 4.03125 in
- Approximate OD of the external thread OD
- 4.46875 in
- Length of the nipple L
- 1.12500 in
- Pilot length l
- 0.25000 in
Ring gages (Table 6)
- GO pitch max / min
- 4.3871 / 4.3865 in
- GO minor max / min
- 4.3179 / 4.3168 in
- NOT GO pitch max / min
- 4.3766 / 4.3760 in
- NOT GO minor max / min
- 4.3500 / 4.3489 in
- Z GO major max / min
- 4.46830 / 4.46810 in
- Z NOT GO major max / min
- 4.44630 / 4.44610 in
Setting plugs (Table 8) and plug gages (Table 7)
- GO truncated major max / min
- 4.4512 / 4.4501 in
- GO full major max / min
- 4.4694 / 4.4683 in
- GO pitch max / min
- 4.3871 / 4.3865 in
- NOT GO truncated major max / min
- 4.4301 / 4.4290 in
- NOT GO pitch max / min
- 4.3766 / 3.3760 in
Notes
- Printed value kept. Misprint: Table 8 col 10 (p. 11), 4-8NPSH, printed NOT GO pitch dia max 4.3766 / min 3.3760; expected min 4.3760. Root radius and tensile stress area are not given in the standard.
- Table 8 col 10 (p. 11), 4-8NPSH: printed NOT GO pitch dia max 4.3766 / min 3.3760; expected min 4.3760
Mates
4-8NPSH EXT screws into a thread of the same standard at the same size and pitch. The standard mating internal thread is class Std. Check the fit with the standard pair →
Working out the mating options…
Different pitch or a different thread family never mate; the fit check runs over both tolerance zones.
Related thread sizes
Same diameter other pitch, and neighbouring sizes
All values for 4-8NPSH EXTevery column of the workbook row
| Designation | 4-8NPSH EXT |
|---|---|
| Decimal / alternate designation | 4.0000-8NPSH EXT |
| Threads per inch | 8 |
| Thread form | NPSH |
| Series | NPSH |
| Series name | Hose to pipe thread (NPSH) |
| External / internal | External |
| Class | Std |
| Nominal size of hose | 4 |
| Pitch P (in.) | 0.12500 |
| Basic major dia D (in.) | 4.4803 |
| Size category | Standard sizes (Tables 1-8) |
| Source table | Table 2 |
| Printed page | 5 |
| Major dia max (in.) | 4.4683 |
| Major dia min (in.) | 4.4461 |
| Major dia tolerance (in.) | 0.0222 |
| Allowance es (in.) | 0.0120 |
| Basic pitch dia D2 (in.) | 4.3991 |
| Pitch dia max (in.) | 4.3871 |
| Pitch dia min (in.) | 4.3760 |
| PD tolerance (in.) | 0.0111 |
| Basic minor dia D1 (in.) | 4.3179 |
| Minor dia max (in.) | 4.3059 |
| Minor dia min (in.) | 4.2768 |
| Minor dia tolerance (in.) | 0.0291 |
| Major dia status | Toleranced (para. 3.1: tolerance = 2 x PD tolerance) |
| Minor dia status | Maximum printed; minimum is a reference value (para. 3.1: P/24 flat at min PD) |
| Root radius max (in.) | not given in the standard |
| Root radius min (in.) | not given in the standard |
| Lead variation ± (in.) (Table 5) | 0.0032 |
| Half-angle variation ± (Table 5) | 1° 42′ |
| Lead variation from PD tol (calc) (in.) | 0.0032 |
| Half-angle variation from PD tol (calc) | 1° 42′ |
| Lead angle at basic PD (deg) | 0.5182 |
| Lead angle (deg min) | 0° 31′ |
| Tensile stress area As (sq in.) | not given in the standard |
| Thread angle (deg) | 60 |
| Flank angle (deg) | 30 |
| Sharp V height H (in.) | 0.108253 |
| Thread height h (in.) | 0.081190 |
| Crest flat, basic P/8 (in.) | 0.015625 |
| Root flat, basic P/8 (in.) | 0.015625 |
| Extreme flat P/24 at minimum PD (in.) | 0.005208 |
| Truncation of the P/8 flat from the sharp V, f = h/6 (in.) | 0.013532 |
| Root radius for model (worn tool) (in.) | 0.013532 |
| Sweep cut: start diameter (in.) | 4.468300 |
| Sweep cut: tip diameter (in.) | 4.305900 |
| Sweep cut: depth (in.) | 0.081200 |
| Sweep cut: profile width at start diameter (in.) | 0.109387 |
| Crest flat as modelled (in.) | 0.015613 |
| Taper | none (straight thread) |
| Service | Steam, air, water, and all other hose connections to be made up with standard pipe threads |
| Mating group (compatible designations) | NPSH-4 |
| Mating member of the same designation | 4-8NPSH INT |
| Other designations in the mating group | none (mates only with its own designation) |
| Min PD clearance: coupling min PD - nipple max PD (in.) | 0.0120 |
| Max PD clearance: coupling max PD - nipple min PD (in.) | 0.0342 |
| Min major dia clearance: coupling min - nipple max (in.) | 0.0120 |
| Min minor dia clearance: coupling min - nipple max (in.) | 0.0120 |
| Fit at the limits (PD) | clearance (always) |
| Table 4 lengths as printed | C 4 1/32; OD 4 15/32; L 1 1/8; l 1/4 |
| Table 4: C inside dia of nipple (in.) | 4.03125 |
| Table 4: approx OD of external thread (in.) | 4.46875 |
| Table 4: L length of nipple (in.) | 1.12500 |
| Table 4: l pilot length (in.) | 0.25000 |
| Table 6 ring gage: GO pitch max (in.) | 4.3871 |
| Table 6 ring gage: GO pitch min (in.) | 4.3865 |
| Table 6 ring gage: GO minor max (in.) | 4.3179 |
| Table 6 ring gage: GO minor min (in.) | 4.3168 |
| Table 6 ring gage: NOT GO pitch max (in.) | 4.3766 |
| Table 6 ring gage: NOT GO pitch min (in.) | 4.3760 |
| Table 6 ring gage: NOT GO minor max (in.) | 4.3500 |
| Table 6 ring gage: NOT GO minor min (in.) | 4.3489 |
| Table 6 ring gage: Z GO major max (in.) | 4.46830 |
| Table 6 ring gage: Z GO major min (in.) | 4.46810 |
| Table 6 ring gage: Z NOT GO major max (in.) | 4.44630 |
| Table 6 ring gage: Z NOT GO major min (in.) | 4.44610 |
| Table 8 setting plug: GO truncated major max (in.) | 4.4512 |
| Table 8 setting plug: GO truncated major min (in.) | 4.4501 |
| Table 8 setting plug: GO full major max (in.) | 4.4694 |
| Table 8 setting plug: GO full major min (in.) | 4.4683 |
| Table 8 setting plug: GO pitch max (in.) | 4.3871 |
| Table 8 setting plug: GO pitch min (in.) | 4.3865 |
| Table 8 setting plug: NOT GO truncated major max (in.) | 4.4301 |
| Table 8 setting plug: NOT GO truncated major min (in.) | 4.4290 |
| Table 8 setting plug: NOT GO full major max (in.) | 4.4694 |
| Table 8 setting plug: NOT GO full major min (in.) | 4.4683 |
| Table 8 setting plug: NOT GO pitch max (in.) | 4.3766 |
| Table 8 setting plug: NOT GO pitch min (in.) | 3.3760 |
| Table 8 setting plug: Full-form GO major max (in.) | 4.4694 |
| Table 8 setting plug: Full-form GO major min (in.) | 4.4683 |
| Table 8 setting plug: Full-form NOT GO major max (in.) | 4.4694 |
| Table 8 setting plug: Full-form NOT GO major min (in.) | 4.4683 |
| Check against formulas | Table 8 col 10 (p. 11), 4-8NPSH: printed NOT GO pitch dia max 4.3766 / min 3.3760; expected min 4.3760 |
| Notes | Printed value kept. Misprint: Table 8 col 10 (p. 11), 4-8NPSH, printed NOT GO pitch dia max 4.3766 / min 3.3760; expected min 4.3760. Root radius and tensile stress area are not given in the standard. |
Related tools
- Thread standardsEvery ISO and ASME thread series and size, with limits and drawings.
- Thread Spec CalculatorDiameters, tolerances and geometry for ISO metric and unified threads.
- Thread Fit CheckPick a bolt and a nut and see the clearance or interference.
- Twist Drill SizesASME B94.11M drills: sizes, lengths, shanks and tolerances.
- Thread Designation GuideHow to read M10×1.5, 1/4-20 UNC-2A, NPT and more.
- Thread Notations & TermsSymbols and terms of a thread profile, explained.
ASME B1.20.7: Hose Coupling Screw Threads, Inch. Source: workbook data (2026-10-10). Confirm against your licensed copy of the standard before use.